Updated November 2026
A pollinator house for your garden gives solitary bees, such as mason bees and leafcutter bees, a safe place to nest and raise their young. This guide walks you through choosing a design, sourcing materials, placing the house correctly and keeping it clean so it stays useful year after year. Most of the work happens in an afternoon, and the payoff is a steady crew of pollinators working your flowers and vegetables.
Choose the Right Design for Your Bees
Solitary bees are not social like honeybees, so they do not need a hive. They need small, dark, dry tubes or holes about 3/8 inch to 5/16 inch in diameter, which is the size most mason bees prefer. Wider holes tend to get filled with mud by the wrong species, so stick to the narrower diameter.
Shopping for one? See our guide: 7 Best Pollinator Garden Seed Mix Options for Bee-Friendly Yards (2026).
You have two main options. A commercial wooden or bamboo nest box is the easiest start. A homemade house is cheaper and lets you control materials, but it takes more care. Either way, the house should have a roof that sheds rain, a back panel to block wind, and an opening that faces east or southeast so the bees warm up in the morning.
Build or Buy Your Pollinator House
If you build your own, use untreated softwood or hardwood at least 3/4 inch thick. Avoid pressure-treated lumber and painted wood, since chemicals can harm developing bees. Drill holes 3/8 inch wide and 4 to 6 inches deep, sanding the entrance smooth so bees do not chew their wings. Leave the back of each hole closed and keep the holes free of splinters.
Bamboo cut into sections also works well. Bundle hollow stems tightly, cut them so each end has a natural node, and trim them to uniform length. Whichever material you choose, make sure nothing is loose enough to let in predators or rain.
Place and Set Up the House
Mount the house about 3 to 6 feet off the ground on a sturdy post, fence or wall. Position it where it gets morning sun and some afternoon shade, ideally within 50 to 100 feet of flowering plants. Keep it away from heavy foot traffic and from sprinklers that might soak the nesting tubes.
Tilt the house slightly forward, about 5 to 10 degrees, so rain runs off rather than pooling inside. Nearby native flowers that bloom in spring make the setup far more attractive to nesting females. Check the official guidance from your state extension service for local timing, since bloom and nesting dates vary by region.
Maintain the Pollinator House Each Year
Pollinator houses need a little seasonal care to stay healthy. Once the tubes are filled and capped, usually by midsummer, carefully remove the nesting material in late fall or early spring. Store cocoons in a cool, dry, rodent-proof container until the following spring, then place them back in the house before bees emerge.
- Clean out old mud, mold or parasites before each season.
- Replace cracked or splintered nesting material.
- Check for mites and fungus, and discard any infested tubes.
- Keep the house away from pesticides and herbicides.
Common Mistakes to Avoid
- Using holes that are too large, which invite the wrong species.
- Hanging the house in full sun all day, which overheats the nests.
- Leaving old nesting material in place year after year.
- Skipping the roof or tilt, which lets rain soak the tubes.
- Placing the house far from any flowers, which makes foraging hard.
Recommended Gear
A good drill bit set in the right diameter makes clean, consistent holes. Look for a View on Amazon so your tubes line up with the sizes solitary bees prefer.
A cocoon storage container protects overwintering bees from moisture and mice. A View on Amazon keeps cocoons cool and dry until spring.
For mounting, a sturdy outdoor post or bracket keeps the house stable and tilted correctly. A View on Amazon lets you position the house at the right height and angle.
FAQ
How high should I hang a pollinator house?
Mount it about 3 to 6 feet off the ground, where it is easy to check but out of casual reach. Height also helps keep nests away from ground-level predators.
Do pollinator houses attract honeybees?
Honeybees do not usually nest in the small tubes solitary bees prefer. Mason and leafcutter bees are the usual residents, though other native species may move in.
How often should I replace the nesting material?
Replace tubes when they become cracked, moldy or heavily parasitized, which is often every two to three years. Clean the house yearly, even if the material looks fine.
Conclusion
A pollinator house for your garden is a simple way to support native bees that work your flowers and crops. Choose the right hole size, place the house in morning sun near blooms, and clean it every year. Check your state extension office for local guidance on timing and native species.

