Updated November 2026

To remove clover from buffalo lawn, you will combine careful identification, targeted hand removal, and better turf management so buffalograss can fill the gaps clover leaves behind. Most of the work happens in spring and early summer, when clover is actively spreading. Done this way, you get a denser buffalo lawn without spraying anything that could harm the bees visiting the clover blooms.

Confirm That It Is Clover

Buffalograss has narrow, blue-green blades and a fine, low growth habit. White clover, the usual intruder, has three rounded leaflets per stem, often with a faint pale chevron, and small white flower heads on long stalks. Clover spreads by stolons that root at the nodes, so a patch often looks like a mat rather than scattered plants. If you are unsure, pull one plant and check the leaves: a clear three-leaflet pattern confirms clover.

Shopping for one? See our guide: How to Remove White Clover from Lawn: 7 Best Clover Killers for 2026.

Remove Clover by Hand and Mow Correctly

Hand-pulling is the most effective method for a small or moderate infestation, and it does not disturb neighboring buffalograss roots. Pull after a rain or deep watering, when the soil is soft enough to lift the whole crown and stolon. Dig out the root crown with a narrow weeding knife or a dandelion tool. Mowing alone will not remove clover, but keeping buffalo grass at its recommended height helps it shade out new clover seedlings.

  1. Water the area the day before so roots release easily.
  2. Loosen the soil around each clover patch with a hand fork.
  3. Lift the plant, roots and all, and shake off the soil.
  4. Fill the hole with a thin layer of compost and tamp it lightly.
  5. Mow buffalo grass at a height of about 2 to 3 inches, never shorter than 2 inches, to keep it competitive.
  6. Repeat monthly during the growing season until new clover stops appearing.

Build Buffalo Grass Density to Crowd Out Clover

Clover thrives in thin, bare, or nitrogen-rich soil. Buffalograss grows best in lean soil and does not need much nitrogen, so over-fertilizing favors clover. Instead, check soil with a basic test kit and use only a light, slow-release organic fertilizer if the test shows a real deficiency. Aerate compacted areas in late spring so buffalo runners can spread into open patches.

Fill Bare Spots Quickly

Where you pull clover, buffalo grass needs a place to grow. Overseed bare areas with buffalograss seed or plugs in late spring, when soil is warm, and keep the top inch moist until germination. This is the step that prevents clover from re-establishing in the same spot.

Use Mulch and Timing to Prevent Regrowth

Clover seeds can persist in the soil for years, so prevention matters as much as removal. Avoid bringing in topsoil or compost that carries clover seed, and use a thin layer of weed-free mulch in bare beds rather than open soil. Time your heaviest pulling for early spring, before clover sets a large seed crop in late spring.

Common Mistakes

  • Using a broadleaf herbicide on buffalograss, which can damage the turf.
  • Pulling clover while it is in full bloom, which spreads pollen-laden seed heads around.
  • Mowing buffalo grass too low, which weakens its ability to compete.
  • Over-fertilizing with nitrogen, which encourages clover growth.
  • Leaving bare soil exposed after removal.

A narrow weeding knife helps you get out the full root crown of clover without tearing up nearby buffalo runners. View on Amazon

A hand fork with short tines makes it easy to loosen soil around clover mats in tight spots. View on Amazon

A soil test kit shows whether nitrogen is high, which tells you whether to hold back fertilizer. View on Amazon

For more background on identifying and controlling clover in turf, see Remove Clover from Lawn Without Chemicals: 6 Steps That Work and Will Clover Take Over My Lawn? How to Keep It in Balance (2026).

FAQ

Can I use a herbicide to remove clover from buffalo lawn?

Many broadleaf herbicides can harm buffalograss and also affect pollinators visiting clover. A non-chemical approach of hand removal and turf management is safer for both. Consult a licensed turf professional before using any product.

How long does it take to get rid of clover in buffalo grass?

Expect a full season or more, since clover seed can remain viable in soil for years. Consistent monthly pulling and overseeding bare spots usually show clear improvement within two growing seasons.

When is the best time to pull clover from buffalo lawn?

Early spring, after rain or watering, is ideal because soil is soft and clover has not yet set seed. Avoid pulling during full bloom to limit seed spread.

Conclusion

Removing clover from buffalo lawn comes down to pulling it by hand, keeping buffalograss mowed at 2 to 3 inches, and avoiding excess nitrogen. Filling bare spots and timing your work around clover’s bloom will keep it from coming back. With steady effort, your buffalo lawn will regain its dense, low-growing character while still supporting the pollinators that visit the clover.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our pollinator-safe lawn care guides, checking product details against manufacturer specifications and owner feedback.